Right here below you can find a lot of extremely good facts pertaining to How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.
Mounting a tub isn't precisely rocket science, but it does call for strong plumbing, woodworking, and sometimes, tiling abilities. Changing an old tub with a new one is also a reasonably tough job. If the old tub is conveniently easily accessible, the job can move speedily; if you need to open a wall surface to eliminate the old tub and also place the new bathtub, the job is a lot harder. In either case, the task is within a residence handyman's skills, although you will require a helper to move out the old bathtub as well as set in the brand-new one. Ensure you have certified yourself for the job and also are comfortable trying it. Instead of hiring a service provider to take over a halfway-completed task, it is much better to consider using one before you start. Possibilities are you may require a professional plumber to make tube links.
This short article will certainly assist you install a brand-new bathtub in your shower room if you have currently purchased a brand-new tub and also don't require to alter the setup of your previous water system pipes.
Your devices and material list ought to consist of the following:
Removing Old Touches
If you require to replace old faucets with new ones as a part of your setup, then the first thing you must do is separate the supply of water. After doing so, activate the taps to drain pipes any water staying in the system. The procedure of removing the existing faucets can be fairly troublesome as a result of the restricted gain access to that is usually the case.
Make use of a basin wrench (crowsfoot spanner) or a tap tool to reverse the nut that connects the supply pipes to the faucets. Have a towel prepared for the continuing to be water that will originate from the pipes. When the supply pipelines have been gotten rid of, use the exact same device to loosen the nut that holds the faucets onto the bath/basin. You will need to quit the single taps from transforming during this process. As soon as the taps have actually been gotten rid of, the holes in the bath/basin will need to be cleansed of any old securing substance.
Before carrying on to fit the brand-new taps, contrast the pipeline connections on the old taps to the brand-new faucets. If the old taps are longer than the brand-new faucets, after that a shank adapter is needed for the new taps to fit.
Fitting New Touches
If the tails of the brand-new faucets are plastic, then you will need a plastic port to avoid damages to the string. One end of the adapter fits on the plastic tail of the faucet and also the other end provides a connection to the existing supply pipelines.
If you require to fit a monobloc, after that you will certainly call for reducing couplers, which connects the 10mm pipe of the monobloc to the conventional 15mm supply pipeline.
Next off, place the faucet in the placing opening in the bath/basin making certain that the washing machines remain in place between the tap and the sink. Secure the tap in place with the producer offered backnut. When the faucet is safely in place, the supply pipes can be linked to the tails of the taps. The taps can either be connected by using corrugated copper piping or with normal tap connectors. The former type should be attached to the tap ends first, tightening only by hand. The supply pipes can later on be attached to the various other end. Tighten up both ends with a spanner after both ends have actually been linked.
Setting up the Tub
Utilizing the two wooden boards under its feet, place the bath tub in the called for placement. The wood boards are practical in uniformly spreading the weight of the bathtub over the area of the boards as opposed to concentrating all the weight onto 4 little points.
The next goal is to make certain that the bath tub is leveled all round. This can be accomplished by inspecting the spirit level and readjusting the feet on the bath tub up until the spirit level reads degree.
To mount faucets, fit the bottom of the furthest adaptable faucet port to the suitable supply pipe by making a compression sign up with; after that do the same for the other faucet.
Turn on the supply of water and examine all joints as well as new pipework for leakages and also tighten them if required. Fill the bath tub as well as also check the overflow electrical outlet as well as the normal electrical outlet for leaks.
Finally, deal with the bathroom paneling as described in the supplier's user's manual. Tiling and securing around the tub ought to wait till the tub has been made use of a minimum of once as this will certainly settle it right into its final position.
Getting ready for the Installation
To start with, the supporting frame provided with the bath needs to be fitted (if needed) according to the manufacturer's directions. Next, fit the faucets or mixer to the bathtub. When suitable the tap block, it is necessary to ensure that if the faucet includes a plastic washer, it is fitted in between the bath as well as the taps. On a plastic bath, it is additionally practical to fit a sustaining plate under the taps device to avoid pressure on the tub.
Fit the adaptable tap adapters to the bottom of the two faucets using 2 nuts as well as olives (sometimes provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and after that pass the outlet via the hole in the bath. Utilize the nut provided by the producer to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the adaptable overflow pipe to the overflow outlet. Afterwards, screw the pipe to the overflow face which ought to be fitted inside the bathroom. Make sure you utilize every one of the supplied washers.
Attach the trap to the bottom of the waste outlet on the bath tub by winding the string of the waste outlet with silicone mastic or PTFE tape, as well as screw on the catch to the outlet. Link all-time low of the overflow tube in a comparable manner.The bath must currently be ready to be fitted in its last placement.
Tiling Around the Bathtub
In the area where the bathroom fulfills the tile, it is required to secure the accompanies a silicone rubber caulking. This is important as the fitting can relocate sufficient to crack a rigid seal, triggering the water to pass through the wall surface between the bath as well as the tiling, causing difficulties with dampness and possible leaks to the ceiling listed below.
You can pick from a selection of coloured sealants to blend in your fixtures as well as installations. They are marketed in tubes and also cartridges, and also are capable of sealing gaps approximately a size of 3mm (1/8 inch). If you have a larger gap to fill, you can load it with spins of soaked newspaper or soft rope. Keep in mind to constantly load the bathtub with water before sealing, to enable the motion experienced when the bathtub remains in usage. The sealer can split relatively early if you do not think about this activity prior to securing.
Conversely, ceramic coving or quadrant floor tiles can be made use of to edge the bath or shower tray. Plastic strips of coving, which are easy to use as well as cut to size, are also easily available on the market. It is suggested to fit the floor tiles making use of waterproof or water-proof glue as well as cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
We were introduced to that write-up about How to Install a Bathtub Yourself from someone on a different web property. Are you aware of another individual who is occupied with the topic? Take a moment to share it. Many thanks for going through it.
Contact